First, the working principle of the dehydrator The main part of the dewatering machine is the inner tank. The inner liner is provided with small holes and air-controlled safety door locks to ensure that the loading door will not open due to human or accidental reasons during the working process of the machine, thus ensuring the safety during work. The clothes to be dehydrated are placed in the liner. The motor drives the inner casing to rotate at a high speed through the belt. Therefore, a large centrifugal force is generated, and the accurately calculated secondary balance weight combined with the high-intensity shock absorbing spring and the car-class special shock absorber constitute a unique non-heavy-type lower suspension structure, which easily resolves vibration and reduces washing noise without special foundation. . The moisture is thus scooped out through the small holes in the inner tank, and is collected and discharged uniformly. Generally speaking, for wet clothes, the drying effect achieved by the dehydrator working for two minutes is almost the same as that achieved by the dryer for twenty minutes, but the dehydrator cannot completely dry the clothes. The main bearing housing with oil-free design is matched with high-quality bearings and imported advanced three-speed waterproof sealing ring. It has strong sealing performance, good durability and reduced maintenance work. Therefore, a way to save time and energy is to dehydrate the wet clothes first, and then dry the water after drying. Large diameter adjustable limit loading door, imported silicone secondary door seal, good sealing and strong durability. Adjustable frequency converter design, adjust the washing or dehydrating speed at any time, and set the optimal washing and dewatering effect for different linens. Intelligent computer control, with uniform distribution and 6-speed dehydration function, ensuring stable and efficient dehydration, and additional over-shock protection function to protect equipment and prolong its service life. 280G-300G dehydration force, avoiding double the motor energy consumption while achieving high dehydration rate, achieving the balance between performance and energy consumption to the greatest extent, saving drying time. Second, the common problems and treatment methods of the dehydrator The dehydrator is one of the washing machines, and is generally used in the water removal process after washing clothes, textile articles, crops and the like. After dehydration and drying with a dryer, the effect of thorough drying can be achieved. The dewatering machine should also pay attention to related problems during installation. For example, the position should be selected in a stable place. The power supply should meet the current required when the machine is running, and the whole machine must be grounded to avoid accidents. After the machine is installed, it needs to be tested before work. Dehydration machine common faults and treatment methods: five common faults and treatment methods of the dehydrator: check whether the power supply voltage is normal. Check that the electrical switch and the filter belt protection are reset. The dehydrator vibration is too large, mainly because the dehydrated items are placed unevenly, individual parts are loose, and then the foundation is solid. After the power is connected, the inner tank does not turn. Please check if the oil is stained on the tape, and clean it in time. Before starting the machine, you must carefully check whether the filter belt deviation detection probe and the filter belt of the machine terminal are over the limit detection board. Correct, manually test whether the correcting device is normal, otherwise the blind opening opportunity will seriously damage the filter belt and switch. The brake device fails or brakes for too long. At this time, we should first check whether the brake joint screw is loose. Secondly, check the belt wear condition and do the corresponding treatment. The drain pipe is blocked. This is a simple look at the water pipe. If there is anything stuffed, clean it up; check the lubrication parts for enough lubrication. Check for leaks at the connection between the pneumatic system line and the valve. Check that all valves in the mud, water, and drug lines are flexible. Open the line manual valve. The bearing housing is hot, and there is a problem with lubrication. Add some lubricant. Place the bottom plane of the movable device, and remove dust and other materials to prevent the movable bearing from moving on the chassis when the machine encounters unbreakable materials, resulting in serious accidents. Rice soup is also called
rice oil. It is a layer of porridge oil that is condensed on the pot
when it is served with fine rice porridge or dried rice. Rice soup is sweet and sweet, it can nourish yin and have a good nourishing effect. Rice Water,Brown Rice Nutrition Juice,No Added Rice Nutrition Juice,Rice Nutrition Juice Ningxia Saiwaixiang Food Co., Ltd. , http://www.nxswxfood.com
The
best rice soup should be made with the unsalted rice and the aleurone
layer. The nutrition and health care function will be the strongest.
With the current refined rice, the effect will not be obvious,
especially after the panning. It`s even less nutritious.
The working principle of the dehydrator, common problems and treatment methods